Made available to the public under the provisions of the Bureau of Indian Standards Act of 1986 and the Right to Information Act of 2005. In order to promote public education and public safety, equal justice for all, a better informed citizenry, the rule of law, world trade and world peace, this legal document is hereby made available on a noncommercial basis, as it is the right of all humans to know and speak the laws that govern them.
Division Name: Production and General Engineering
Section Name: Metal Forming Machines (PGD 4)
| Standard | Year | Title | IBR |
|---|---|---|---|
| IS 2515 (pdf) | 1978 | Test chart for guillotine shears | |
| IS 4296-1 (pdf) | 2002 | Tools for Pressing, Part 1: Round Punches with 60 Conical Head and Straight Shank | ISO 6752 |
| IS 4296-2 (pdf) IS 4296-2 (txt) | 2002 | Tools for Pressing, Part 2: Round Punches with Cylindrical Head and Reduced Shank | ISO 8021 |
| IS 4296-3 (pdf) | 2002 | Tools for Pressing, Part 3: Round Punches with Cylindrical Head and Straight Shank | |
| IS 4296-4 (pdf) | 2002 | TOOLS FOR PRESSING, Part 4: ROUND PUNCHES WITH 60 ' CONICAL HEAD AND REDUCED SHANK | ISO 8021 |
| IS 4592 (pdf) | 2002 | Acceptance Conditions of Open Front Mechanical Power Presses - Testing of Accuracy | ISO 6899 |
| IS 4593 (pdf) | 1968 | Test chart for straight-sided presses | |
| IS 4918 (pdf) IS 4918 (txt) | 1981 | Hard Metal (Carbide) Wire, Bar and Tube Drawing Dies | ISO 1684 |
| IS 6652-1 (pdf) IS 6652-1 (txt) | 1986 | Glossary of terms relating to metal forming machines and tools, Part 1: Metal forming tools | |
| IS 6652-2 (pdf) IS 6652-2 (txt) | 1986 | Glossary of terms relating to metal forming machines and tools, Part 2: Metal forming machines relating to sheet metal | |
| IS 6652-3 (pdf) IS 6652-3 (txt) | 1986 | Glossary of terms relating to metal forming machines and tools, Part 3: Metal forming technology and operations relating to sheet metal | |
| IS 7468 (pdf) | 1974 | Recommendation on preferred strokes for mechanical and hydraulic presses | |
| IS 7469 (pdf) | 1974 | Recommendation on preferred capacities for mechanical and hydraulic presses | |
| IS 7664 (pdf) | 2005 | Guide Posts for Press Tool Sets | |
| IS 7706 (pdf) | 1975 | Bolster Plates for Gap Frame Presses without Die Cushion | |
| IS 7707 (pdf) | 1975 | Bolster Plates for Gap Frame Presses with Die Cushion | |
| IS 8064 (pdf) | 2002 | Method of Designation of Mechanical and Hydraulic Presses | |
| IS 8127 (pdf) | 2005 | Guide Bushes for Press Tool Die Sets | |
| IS 8711 (pdf) IS 8711 (txt) | 2002 | Gap Frame Open Front Mechanical Presses - Capacity Ratings and Dimensions | |
| IS 9266-1 (pdf) | 1979 | Press Working Die Sets (Boss Type) - Part I : Centre Post Rectangular Die Sets | |
| IS 9266-2 (pdf) | 1979 | Press Working Die Sets (Boss Type) - Part II : Centre Post Square Die Sets | |
| IS 9266-3 (pdf) | 1979 | Press Working Die Sets (Boss Type) - Part III : Centre Post Round Die Sets | |
| IS 9266-4 (pdf) | 1990 | Press Working Die Sets (Boss Type) , Part 4: Centre Post Reverse Rectangular Die Sets | |
| IS 9888 (pdf) | 1981 | Dimensions for sintered pellets of hard metal (carbide) for wire, bar and tube drawing dies | ISO 2804 |
| IS 10068-1 (pdf) | 1982 | Press Working Die Sets (plain type) - Part I : Centre Post Rectangular Die Sets | |
| IS 10068-2 (pdf) | 1982 | Press Working Die Sets (plain type) - Part II : Centre Post Square Die Sets | |
| IS 10068-3 (pdf) | 1990 | Press Working Die Sets - Plain Type, Part 3: Centre Post Round Die Sets | |
| IS 10068-4 (pdf) | 1997 | Press Working Die Sets (Plain Type), Part 4: Rear Post Rectangular Die Sets | |
| IS 10068-5 (pdf) | 1996 | Press Working Die Sets (Plain Type), Part 5: Rear Post Square Die Sets | |
| IS 10068-6 (pdf) | 1996 | Press Working Die Sets (Plain Type), Part 6: Rear Post Round Die Sets | |
| IS 10644 (pdf) | 1983 | Recommendation on preferred shut heights for mechanical presses | |
| IS 10650 (pdf) | 1983 | Pressure Pins | |
| IS 10731 (pdf) | 2000 | Presses - Slide Holes for Locating the Shanks - Dimensions | |
| IS 11344 (pdf) | 1985 | Dimensions for sintered carbide pellets used in heading dies | ISO 5407 |
| IS 11372 (pdf) IS 11372 (txt) | 1985 | Proforma for purchase specification and technical features for belt drop hammers | |
| IS 11443-1 (pdf) | 2003 | Tool for Pressing and Moulding - Machined Plates : Part 1 - Machined Plates for Press Tools, Jigs and Fixtures | ISO 6753-1 |
| IS 11443-2 (pdf) IS 11443-2 (txt) | 2003 | Tools for Pressing and Moulding - Machined Plates, Part 2: Machined Plates for Moulds | ISO 6753-2 |
| IS 11505 (pdf) | 1986 | Recommendations on terminology of hardmetal heading dies | ISO 5396 |
| IS 11524 (pdf) | 1986 | Carbide Mandrels for Tube Drawing Dies (ISO Title : Tube Drawing Mandrels) | ISO 1651 |
| IS 11684 (pdf) | 1986 | Test chart for spinning and planishing lathes | |
| IS 11742 (pdf) | 1986 | Test chart for die sets | |
| IS 12665-1 (pdf) | 1989 | Press working tools - Shanks, Part 1: General dimensions and survey | |
| IS 12665-2 (pdf) | 1989 | Press working tools - shanks, Part 2: Shanks to suit riveting | |
| IS 12665-3 (pdf) | 1989 | Press working tools - shanks, Part 3: Shanks with screwed shaft | |
| IS 12665-4 (pdf) | 1989 | Press working tools - shanks, Part 4: Shanks with neck and collar | |
| IS 12665-5 (pdf) | 1996 | Press working tools - Shanks, Part 5: Shanks with square flanges | |
| IS 12665-6 (pdf) IS 12665-6 (txt) | 1996 | Press Working Tools - Shanks, Part 6: Shanks with Rectangular Flanges | |
| IS 12665-7 (pdf) | 1996 | Press Working Tools - Shanks, Part 7: Shanks with Screwed Shaft and Collar | |
| IS 12852 (pdf) | 1989 | Gap frame hydraulic presses up to 4000 KN - Recommendation on preferred capacities and dimensions | |
| IS 12984 (pdf) IS 12984 (txt) | 1990 | Proforma for purchase specification for plate bending machines | |
| IS 14497 (pdf) | 1997 | Capacity rating and dimensions for trimming presses | |
| IS 14757 (pdf) | 2000 | Recommendations on Preferred Capacities and Dimensions for Straight-sided Column Type and Four Pillar Type Hydraulic Presses | |
| IS 14758 (pdf) IS 14758 (txt) | 2000 | Forging Machine Tools - Glossary of Terms | |
| IS 14877-1 (pdf) IS 14877-1 (txt) | 2000 | Hydraulic Presses - Straight Sided Column/C-Frame Type, Part 1: Test Chart for Geometrical Accuracy | |
| IS 14877-2 (pdf) IS 14877-2 (txt) | 2002 | Hydraulic Presses - Straight Sided Columns/C-Frame Type, Part 2: Test Chart for Technical (Performance) Evaluation of Presses and Press Brakes | |
| IS 14878 (pdf) IS 14878 (txt) | 2000 | Test Chart for Plate Bending Machines | |
| IS 15300 (pdf) | 2002 | Tools for Pressing - Punches - Nomenclature and Terminology | ISO 8695 |
| IS 15318 (pdf) IS 15318 (txt) | 2003 | Open Front Mechanical Power Presses - Vocabulary | ISO 8540 |
| IS 15424-1 (pdf) | 2004 | Tools for Pressing - Guide Pillars, Part 1: Types | ISO 9182-1 |
| IS 15424-2 (pdf) | 2004 | Tools for Pressing - Guide Pillars, Part 2: Type A, Straight Pillars | ISO 9182-2 |
| IS 15424-3 (pdf) | 2004 | Tools for Pressing - Guide Pillars, Part 3: Type B, End-Locking Pillars | ISO 9182-3 |
| IS 15424-4 (pdf) | 2004 | Tools for Pressing - Guide Pillars, Part 4: Type C, Pillars with Taper Lead and Bush | ISO 9182-4 |
| IS 15424-5 (pdf) | 2004 | Tools for Pressing - Guide Pillars, Part 5: Type D, End-Locking Pillars with Flange | ISO 9182-5 |
| IS 15448-1 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 1: Forms | ISO 9448-1 |
| IS 15448-2 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 2: Form A, Gliding Bushes, Plain, Type 1 | ISO 9448-2 |
| IS 15448-3 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 3: Form B, Ball Cage Bushes, Plain, Type 1 | ISO 9448-3 |
| IS 15448-4 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 4: Form C, Gliding Bushes, Headed, Type 1 | ISO 9448-4 |
| IS 15448-5 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 5: Form D, Ball Cage Bushes, Headed, Type 1 | ISO 9448-5 |
| IS 15448-6 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 6: Form E, Gliding Bushes, Flanged, Type 1 | ISO 9448-6 |
| IS 15448-7 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 7: Form F, Ball Cage Bushes, Flanged, Type 1 | ISO 9448-7 |
| IS 15448-8 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 8: Form G, Gliding Bushes, Stepped, Type 1 | ISO 9448-8 |
| IS 15448-9 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 9: Form B, Ball Cage Bushes, Plain, Type 2 | ISO 9448-9 |
| IS 15448-10 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 10: Form E, Gliding Bushes, Flanged, Type 2 | ISO 9448-10 |
| IS 15448-11 (pdf) | 2004 | Tools for Pressing - Guide Bushes, Part 11: Form F, Ball Cage Bushes, Flanged, Type 2 | ISO 9448-11 |
| IS 15744 (pdf) | 2007 | Angular deflection for 'C' frame mechanical presses | |
| IS 15745 (pdf) | 2007 | Deflection for straight sided mechanical presses | |
| IS 15746 (pdf) | 2007 | Angular deflection for 'C' frame mechanical Hydraulic press | |
| IS 15747 (pdf) | 2007 | Angular deflection for straight sided hydraulic presses |
Last Updated: September 6, 2013
↑